APRIMATIC ONDA 801 PDF

aprimatic onda e z16 aprimatic onda aprimatic aprimatic xt aprimatic xt 44 installazione aprimatic zt4b service service aprimatic at par. Onda Электромеханический привод для откатных ворот массой до кг собственностью компании APRIMATIC S.p.a. и не могут быть. This manual. Product description. Kit indianapolis Wave kit for sliding doors and residential use condominiale. The kit includes: n ° 1 gearmotor degree Onda ;.

Author: Yozshucage Daigami
Country: Lebanon
Language: English (Spanish)
Genre: Marketing
Published (Last): 23 October 2006
Pages: 450
PDF File Size: 17.51 Mb
ePub File Size: 9.44 Mb
ISBN: 927-5-49399-439-5
Downloads: 74218
Price: Free* [*Free Regsitration Required]
Uploader: Malajar

With internal control unit Adjustable torque limiter clutch on fast shaft. The wheels must be appropriate to the type of slides used. The wheels must match the guide profile and must be in good condition. Aprimatic supplies different types of wheels; the sizes and relative capacities are indicated in figure B3.

When choosing the wheels, apart from the bearing, it must be considered that greater is the diameter, better is the sliding movement of the gates. D – Aprimatic microprocessor control unit shelter, where possible, from atmospheric agents or inside the geared-motor Note: With wooden gates, it is better to use the plastic rack by verifying the good conditions aprimati the wood in the fixing points.

In some areas where heavy snow occurs or there are flooding risks the geared-motor can be placed at a height of cm.

A description is also given of the typical layout that must be controlled when the site is inspected see also fig. C11 for the layout and the positioning of the rack.

ATTENTION It is essential that, when the site is inspected, the installer makes sure that there is sufficient room near the gate for the layouts illustrated in the drawings. The geared-motor must be correctly aligned with the gate guide, at the correct distance from the gate, at the right depth, and the electric cable passage bore in the correct position C2.

Foundation plate positioning Execute a hole for the fitting of the cables for 30 mm diameter tubes MAX. Refer to them when mounting the cover see D8 page The A measurement depends on the type of pinion and the type of rack used see tables in C A – Plastic rack with a steel core B – Galvanized Steel rack In both, the length of each piece is 1 m.

It is simple to install without the need of welding. The plastic rack is normally fixed to the gate with screws. Four self-tapping screws for each piece are provided in the kit which are aprkmatic as in C The ondx supports must be welded to the gate C It is advisable to weld the entire circumference. C 19 Spirit level C 20 Rest the first rack section on the geared-motor pinion ojda move the spacers in contact with the gate until the first hole complete with screw and spacer is lined up with the vertical axis of the pinion C19then fix the spacer to the gate with a spot weld.

  HILDEBRANDSLIED TEXT PDF

The T2B control unit can be also installed inside the geared motor; in these case see further instruction in appendix. It is activated by two metal plates D3 that are fitted on the rack and come into contact with the switch in the fully open and fully closed gate positions D4.

Move the gate to the closed position leaving sufficient space to guarantee the braking distance and safety clearance. Follow the same procedure for the open end travel plate. The adjustment of the clutch and all the safety devices must be per- formed only by qualified personnel. The clutch intervenes by limiting the pressure of the gate on any obstacle in its path.

Aprimatic ONDA Manuals

The fixing 8801 are the same used in the box of the control unit. The release system that disengages the pinion allows the manual opening of the gate. To release the geared-motor just insert the triangular key F1 in the special lock and turn it half way round in a clockwise direction; In order to lock it, perform the operation in reverse order and ensure correct aaprimatic by pushing the gate a few centimetres.

To avoid incorrect manoeuvres and the consequent risk of accidents, it is important to read this manual carefully, strictly observing the instructions given. Device for Aprimatic operators to operate swing gates.

Device with Aprimatic microprocessor 15 Watt in stand-by designed to drive 1 motor with a maximum power of Watt. Secure the device at a minimum height of 30 cm, using the securing holes in the plastic container. Insert the connecting cables, through the holes in the bottom aprjmatic the container and the cable clamps indicated. The adjustment range of the pause time is between 0 and seconds. Standard Apeimatic Immediate re-closure Trimmer P2 – This aprmatic is used to adjust the intensity of the electronic brake, to Page of 31 Go.

Le informazioni sono dirette agli operatori esperti che eseguono l’installazione e la manutenzione straordinaria. Essi devono possedere competenze specifiche. This manual has been prepared by the manufacturer and is an integral part of the product.

aprimatic onda e z16 manual – wechwech Recherche

The information is aimed at expert installers and those carrying out extraordinary maintenance operations. These persons must be specifically qulified to carry out this work correctly and under the maximum safety conditions. Scrupulous observance of the instructions will ensure safety for man, economic running and a long product functioning life. To avoid incorrect manoeuvres and. As this is a product to be installed in residential buildings, the expert installer, after completing installation must verify that this has been performed correctly and.

  DE WERELD VOLGENS GARP PDF

Subsequently, it is necessary to instruct the user on the correct use of the product providing all the documentation envisaged. Este manual ha sido redactado por el constructor y forma para integrante del producto. Las informaciones que contiene van dirigidas a los operadores. Add to my manuals Add. Page 5 The wheels must match the guide profile and must be in good condition. Page 7 With wooden gates, it is better to use the plastic rack by verifying the good conditions of the wood in the fixing points.

Page 9 A description is also given of the typical layout that must be controlled when the site is inspected see also fig. Page 13 The A measurement depends on the type of pinion and the type of rack used see tables in C Page 16 C 19 Spirit level C 20 Rest the first rack section on the geared-motor pinion and move the spacers in contact with the gate until the first hole complete with screw and spacer is lined up with the vertical axis of the pinion C19then fix the spacer to the gate with a spot weld.

Page 21 The adjustment of the clutch and all the safety devices must be per- formed only by qualified personnel. Page 25 The release system that disengages the pinion allows the manual opening of the gate.

Page 26 Installation instructions Page 27 To avoid incorrect manoeuvres and the consequent risk of accidents, it is important to read this manual carefully, strictly aprimaticc the instructions given. Page 28 Device with Aprimatic microprocessor 15 Watt in stand-by designed to drive 1 motor with a maximum power of Watt.

Page 31 3 seconds and the closing. This manual also for: Comments to this Manuals Your Name.

wechwech Recherche

Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it.

Don’t show me this message again. Got it, continue to print. Don’t have an account?